Replicant

h1. GTI9000Bootloader

h2. Boot log

<pre>

reading nps status file is successfully!.

nps status=0x504d4f43

PMIC_IRQ1    = 0xc0 

PMIC_IRQ2    = 0x0 

PMIC_IRQ3    = 0x0 

PMIC_IRQ4    = 0x0 

PMIC_STATUS1 = 0x80 

PMIC_STATUS2 = 0x0 

get_debug_level current debug level is 0x574f4c44.

aries_process_platform: Debug Level Low

keypad_scan: key value ----------------->= 0x40

CONFIG_ARIES_REV:48 , CONFIG_ARIES_REV03:48 

aries_process_platform: final s1 booting mode = 0

DISPLAY_PATH_SEL[MDNIE 0x1]is on

MDNIE setting Init start!!

vsync interrupt is off

video interrupt is off

[fb0] turn on

MDNIE setting Init end!!

Autoboot (0 seconds) in progress, press any key to stop 

get_debug_level current debug level is 0x574f4c44.

get_debug_level current debug level is 0x574f4c44.

boot_kernel: Debug Level Low

FOTA Check Bit 

 Read BML page=, NumPgs=

FOTA Check Bit (0xffffffff)

Load Partion idx = (6)

..............................done

Kernel read success from kernel partition no.6, idx.6.

setting param.serialnr=0xxxxxxxxx 0xxxxxxxxx

setting param.board_rev=0x30

setting param.cmdline=console=ttySAC2,115200 loglevel=4

Starting kernel at 0x32000000...

</pre>

h2. Available commands

Here are the available commands:

<pre>

SBL> help  

Following commands are supported:

* setenv

* saveenv

* printenv

* help

* reset

* boot

* kernel

* format

* open

* close

* erasepart

* eraseall

* loadkernel

* showpart

* addpart

* delpart

* savepart

* nkernel

* nramdisk

* nandread

* nandwrite

* usb

* mmctest

* keyread

* usb_read

* usb_write

* fuelgauge

* pmic_read

* pmic_write

To get commands help, Type "help <command>"

</pre>

Environment related commands:

<pre>

SBL> help setenv

* Help : setenv

* Usage : setenv [name] [value] . .

	Modify current environment info on ram

SBL> help saveenv

* Help : saveenv

* Usage : saveenv

	Save cuurent environment info to flash

SBL> help printenv

* Help : printenv

* Usage : printenv

	Print current environment info on ram

</pre>

Partition related commands:

<pre>

SBL> help erasepart

* Help : erasepart

* Usage : erasepart partition_id

	erase part of units

       - ex) erase 0x9(temp partition)

SBL> help eraseall

* Help : eraseall

* Usage : eraseall

	erase all units

SBL> help showpart

* Help : showpart

* Usage : showpart

	show partition information

SBL> help addpart

* Help : addpart

* Usage : addpart <id> <attr> <unit>

	add partition information

       - ex) addpart 0x(id) 0x1(attr) 0x10(units)

SBL> help delpart

* Help : delpart

* Usage : delpart

	delete last partition information

SBL> help savepart

* Help : savepart

* Usage : savepart

	save partition information

</pre>

Boot related commands:

<pre>

SBL> help boot

* Help : boot

* Usage : boot [kernel options]

Boot Linux with optional kernel options

SBL> help kernel

* Help : kernel

* Usage : kernel hex_adr

Change the Linux kernel base

SBL> help loadkernel

* Help : loadkernel

* Usage : loadkernel

	load kernel image

       - loadkernel 0x80A00000 from kernel partition

SBL> help nkernel

* Help : nkernel

* Usage : nkernel command

* Usage : nkernel

	read kernel from flash to DDR

SBL> help nramdisk

* Help : nramdisk

* Usage : nramdisk command

* Usage : nramdisk

	read ramdisk from flash to DDR

SBL> help nandread

* Help : nandread

* Usage : * Usage : nandread <PARTID> <SIZE>

	read partition from flash to SDRAM(0x80000000)

SBL> help nandwrite

* Help : nandwrite

* Usage : * Usage: nandwrite <PARTID> <SIZE>

	write partition from SDRAM(0x80000000) to flash

</pre>

Other commands:

<pre>

SBL> help help

* Help : help

* Usage : help [command]

SBL> help reset

* Help : reset

* Usage : reboot

Reboot system

SBL> help format

* Help : format

* Usage : format

	format device

SBL> help open

* Help : open

* Usage : open

	open device

SBL> help close

* Help : close

* Usage : close

	close device

SBL> help usb

* Help : usb

* Usage : usb download command

SBL> help mmctest

* Help : mmctest

* Usage : *Usage : mmctest 

SBL> help keyread

* Help : keyread

* Usage : *Usage : keyread 

SBL> help usb_read

* Help : usb_read

* Usage : usb_read reg

Read the usb ic register

SBL> help usb_write

* Help : usb_write

* Usage : usb_write reg, val

Read the usb ic register

SBL> help fuelgauge

* Help : fuelgauge

* Usage : *usage : fuelgauge

SBL> help pmic_read

* Help : pmic_read

* Usage : pmic_read reg

Read the pmic register

SBL> help pmic_write

* Help : pmic_write

* Usage : pmic_write reg, val

Read the pmic register

SBL> 

</pre>

h2. Environment

<pre>

SBL> printenv

PARAM Rev 1.3

SERIAL_SPEED : 7

LOAD_RAMDISK : 0

BOOT_DELAY : 0

LCD_LEVEL : 97

SWITCH_SEL : 1

PHONE_DEBUG_ON : 0

LCD_DIM_LEVEL : 0

LCD_DIM_TIME : 6

MELODY_MODE : 1

REBOOT_MODE : 3

NATION_SEL : 0

LANGUAGE_SEL : 0

SET_DEFAULT_PARAM : 0

PARAM_INT_13 : 0

PARAM_INT_14 : 0

VERSION : I9000XXIL

CMDLINE : console=ttySAC2,115200 loglevel=4

DELTA_LOCATION : /mnt/rsv

PARAM_STR_3 : 

PARAM_STR_4 : 

</pre>