GalaxyNexusI9250SerialConsole » History » Revision 6
Revision 5 (Denis 'GNUtoo' Carikli, 11/03/2012 11:58 AM) → Revision 6/22 (Denis 'GNUtoo' Carikli, 11/03/2012 12:01 PM)
h1. GalaxyNexusSerialConsole
* http://redmine.replicant.us/projects/replicant/wiki/S5PC110Bootloader works as a serial cable.
When you connect the cable you get the FIQ debugger, but what if you want kgdb instead:
* apply that patch:
<pre>
diff --git a/arch/arm/mach-omap2/board-tuna.c b/arch/arm/mach-omap2/board-tuna.c
index a022a43..7098227 100644
--- a/arch/arm/mach-omap2/board-tuna.c
+++ b/arch/arm/mach-omap2/board-tuna.c
@@ -1001,6 +1001,8 @@ static inline void __init board_serial_init(void)
omap_serial_init_port_pads(0, uart1_pads, uart1_pads_sz, NULL);
omap_serial_init_port_pads(1, tuna_uart2_pads,
ARRAY_SIZE(tuna_uart2_pads), &tuna_uart2_info);
+ omap_serial_init_port_pads(2,tuna_uart3_pads,
+ ARRAY_SIZE(tuna_uart3_pads), NULL);
omap_serial_init_port_pads(3, tuna_uart4_pads,
ARRAY_SIZE(tuna_uart4_pads), NULL);
}
</pre>
* remove the FIQ debugger in the kernel configuration.
* change the CMDLINE trough the kernel configuration:
Use:
<pre>CONFIG_CMDLINE="console=ttyO2 androidboot.console=ttyO2 [...]"</pre>
Instead of:
<pre>CONFIG_CMDLINE="console=ttyFIQ0 androidboot.console=ttyFIQ0 [...]"</pre>
* Verify that you get the kernel messages.
* Then change the cmdline for kgdb
<pre>
CONFIG_CMDLINE="kgdboc=ttyO2,115200 console=ttyO2 androidboot.console=ttyO2 [...]"
</pre>
Don't add kgdbwait tough because it result in that:
<pre>
(gdb) set remotebaud 115200
(gdb) target remote /dev/ttyUSB0
/dev/ttyUSB0: Device or resource busy.
(gdb) target remote /dev/ttyUSB0
Remote debugging using /dev/ttyUSB0
kgdb_breakpoint ()
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/debug/debug_core.c:954
954 arch_kgdb_breakpoint();
(gdb) c
Continuing.
Program received signal SIGSEGV, Segmentation fault.
__raw_spin_lock_irqsave (lock=0x288)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/spinlock.c:112
112 BUILD_LOCK_OPS(spin, raw_spinlock);
(gdb) bt
#0 __raw_spin_lock_irqsave (lock=0x288)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/spinlock.c:112
#1 0xc061aecc in _raw_spin_lock_irqsave (lock=0x288)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/spinlock.c:145
#2 0xc0098620 in try_to_wake_up (p=0x0, state=1611595795, wake_flags=1)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/sched.c:2681
#3 0xc009897c in wake_up_process (p=0x288)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/sched.c:2785
#4 0xc00e2090 in proc_dohung_task_timeout_secs (table=<value optimized out>, write=<value optimized out>,
buffer=<value optimized out>, lenp=<value optimized out>, ppos=0xc782bf70)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/kernel/hung_task.c:190
#5 0xc0174178 in proc_sys_call_handler (filp=<value optimized out>, buf=0x24808, count=1, ppos=0xc782bf70,
write=1) at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/fs/proc/proc_sysctl.c:158
#6 0xc01741b0 in proc_sys_write (filp=0x288, buf=0x600f0013 <Address 0x600f0013 out of bounds>, count=1,
ppos=0xc782a000)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/fs/proc/proc_sysctl.c:176
#7 0xc0126420 in vfs_write (file=0xc73be500, buf=0x24808 "0", count=<value optimized out>, pos=0xc782bf70)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/fs/read_write.c:377
#8 0xc0126590 in sys_write (fd=<value optimized out>, buf=0x24808 "0", count=1)
at /home/gnutoo/embedded/android/replicant-4.0/kernel/samsung/tuna/fs/read_write.c:429
#9 0xc0055a00 in ?? ()
Cannot access memory at address 0x0
#10 0xc0055a00 in ?? ()
Cannot access memory at address 0x0
Backtrace stopped: previous frame identical to this frame (corrupt stack?)
</pre>
* disable the watchdot timer.
At the end the cmdline should look like that:
<pre>
CONFIG_CMDLINE="kgdboc=ttyO2,115200 console=ttyO2 androidboot.console=ttyO2 mem=1G vmalloc=768M omap_wdt.timer_margin=0 no_console_suspend"
</pre>
then open a root console and do:
<pre>
echo g > /proc/sysrq-trigger
</pre>