h1. I9250Bootloader
{{toc}}
h2. Accessing the bootloader console
When connected on the serial port, during boot, if you press the volume down button and press enter on the serial console, you can get a shell:
====== VCELL : 409625, SOC : 100, nType : 4 ======
[Charger] nScaledVCELL : 409625000, nDesriedSOC, : 98, nMaxSOC : 118, nMinSOC : 78
* FB base addr = 0xbea70000!
* PANEL_S6E8AA0_ID_READ : 0x12, 0x8e, 0x9b.
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
Autoboot (1 seconds) in progress, press any key to stop .
Autoboot aborted..
SBL>
SBL>
SBL>
SBL> help
Following commands are supported:
* setenv
* saveenv
* printenv
* help
* reset
* boot
* kernel
* loadpart
* loadkernel
* erasepart
* omap_upload_rdx
* omap_test_button
* omap_test_hwinfo
* omap_set_gpio_level
* omap_get_gpio_level
* omap_test_twl6030
* omap_test_power
* omap_reboot
* omap_halt
* omap_cmdline_power
* omap_test_kbd
* omap_test_usbacc
* usb
* omap_test_max17043
* omap_test_fsa9480
* omap_dump_sec_log_buf
* omap_test_sud
To get commands help, Type "help "
SBL>
h2. Available commands
Here's the known list of commands:
SBL> help
Following commands are supported:
* setenv
* saveenv
* printenv
* help
* reset
* boot
* kernel
* loadpart
* loadkernel
* erasepart
* omap_upload_rdx
* omap_test_button
* omap_test_hwinfo
* omap_set_gpio_level
* omap_get_gpio_level
* omap_test_twl6030
* omap_test_power
* omap_reboot
* omap_halt
* omap_cmdline_power
* omap_test_kbd
* omap_test_usbacc
* usb
* omap_test_max17043
* omap_test_fsa9480
* omap_dump_sec_log_buf
* omap_test_sud
To get commands help, Type "help "
SBL>
And their respective help:
SBL> help setenv
* Help : setenv
* Usage : setenv [name] [value] . .
Modify current environment info on ram
SBL> help saveenv
* Help : saveenv
* Usage : saveenv
Save cuurent environment info to flash
SBL> help printenv
* Help : printenv
* Usage : printenv
Print current environment info on ram
SBL> help help
* Help : help
* Usage : help [command]
SBL> help reset
* Help : reset
* Usage : reboot
Reboot system
SBL> help boot
* Help : boot
* Usage : boot [kernel options]
Boot Linux with optional kernel options
SBL> help kernel
* Help : kernel
* Usage : kernel hex_adr
Change the Linux kernel base
SBL> help loadpart
* Help : loadpart
* Usage : load partition from storage device.
SBL> help loadkernel
* Help : loadkernel
* Usage : load kernel from storage device.
SBL> help erasepart
* Help : erasepart
* Usage : erase partition.
SBL> help omap_upload_rdx
* Help : omap_upload_rdx
* Usage : [OMAP] upload RDX
omap_upload_rdx
SBL> help omap_test_button
* Help : omap_test_button
* Usage : [OMAP] test OMAP buttons
omap_test_button
SBL> help omap_test_hwinfo
* Help : omap_test_hwinfo
* Usage : [OMAP] test OMAP HW Information
omap_test_hwinfo
SBL> help omap_set_gpio_level
* Help : omap_set_gpio_level
* Usage : [OMAP] set GPIO level
omap_set_gpio_level {GPIO} {VALUE}
SBL> help omap_get_gpio_level
* Help : omap_get_gpio_level
* Usage : [OMAP] get GPIO level
omap_get_gpio_level {GPIO}
SBL> help omap_test_twl6030
* Help : omap_test_twl6030
* Usage : [OMAP] test twl6030 device
omap_test_twl6030
SBL> help omap_test_power
* Help : omap_test_power
* Usage : [OMAP] test power function
omap_test_power
SBL> help omap_reboot
* Help : omap_reboot
* Usage : [OMAP] system reboot command
omap_reboot
SBL> help omap_halt
* Help : omap_halt
* Usage : [OMAP] system halt command
omap_halt
SBL> help omap_cmdline_power
* Help : omap_cmdline_power
* Usage : [OMAP] check kernel-cmdline by power
omap_cmdline_power
SBL> help omap_test_kbd
* Help : omap_test_kbd
* Usage : [OMAP] test power function
omap_test_kbd
SBL> help omap_test_usbacc
* Help : omap_test_usbacc
* Usage : [OMAP] test OMAP usb-accessary
omap_test_usbacc
SBL> help usb
* Help : usb
* Usage : usb download command
SBL> help omap_test_max17043
* Help : omap_test_max17043
* Usage : [OMAP] test max17043 device
omap_test_max17043
SBL> help omap_test_fsa9480
* Help : omap_test_fsa9480
* Usage : [OMAP] test fsa9480 device
omap_test_fsa9480
SBL> help omap_dump_sec_log_buf
* Help : omap_dump_sec_log_buf
* Usage : [OMAP] dump sec-log-buf
omap_dump_sec_log_buf
SBL> help omap_test_sud
* Help : omap_test_sud
* Usage : [OMAP] test SUD image
omap_test_sud {NUMBER}
SBL>
h2. Changing the kernel commandline arguments
I've tried to modify the CMDLINE:
SBL> setenv CMDLINE loglevel=8 console=ttyFIQ0 androidboot.console=ttyFIQ0
argv[0] : setenv
argv[1] : CMDLINE
argv[2] : loglevel=8 console=ttyFIQ0 androidboot.console=ttyFIQ0
value : 656175548
SBL> saveenv
save_param start block=49152, no.blocks=16384
But once booted, "loglevel=8" wasn't found in /proc/cmdline on Replicant 6.0 0003 so it doesn't seem to have an impact. Though, on this bootloader, the commandline can also be modified by modifying the boot.img commandline parameters.
h2. Other commands
SBL> omap_test_hwinfo
-----------------------------------------------------------
OMAP-Samsung HW Information
Board Name : tuna REV 9
Board Rev : HSPA - 9
Boot Type : USB MMC1
Device Type : HS
Build Date : Jan 24 2012 18:27:20
-----------------------------------------------------------
SBL> printenv
PARAM Rev 1.6
SERIAL_SPEED : 7
LOAD_RAMDISK : 0
BOOT_DELAY : 1
LCD_LEVEL : 6
SWITCH_SEL : 3
PHONE_DEBUG_ON : 0
LCD_DIM_LEVEL : 0
LCD_DIM_TIME : 6
MELODY_MODE : 1
REBOOT_MODE : 0
NATION_SEL : 0
LANGUAGE_SEL : 0
SET_DEFAULT_PARAM : 0
OFF_MODE_CHARGE : 1
FLASH_LOCK_STATUS : 0
VERSION :
CMDLINE :
DELTA_LOCATION : /mnt/rsv
WIFI_MAC_LINE :
PARAM_STR_4 : DCM